MTS to AVI Converter: How to Fix Problem - Default Gateway Windows 7 64 Bit?

Default Gateway Windows 7 64 Bit

I have been following this thread and using the suggested fixes (ie; bonjour) without success, having the same problem whereby I lose my connection due to a default gateway problem.

I do not have bonjour and I lose my connection about once per hour.
I purchased this machine native with Windows 7, so no upgrade paths or issues exist.
Use it as it came out of the box.

Network adapter Local Area Connection driver information:
Description .
.
.
.
.
.
.
.
.
.
: Intel(R) 82578DC Gigabit Network Connection
Manufacturer .
.
.
.
.
.
.
.
.
: Intel
Provider .
.
.
.
.
.
.
.
.
.
.
: Intel
Version .
.
.
.
.
.
.
.
.
.
.
: 11.0.41.0
Inf File Name .
.
.
.
.
.
.
.
.
: C:\Windows\INF\oem2.inf
Inf File Date .
.
.
.
.
.
.
.
.
: Monday, June 22, 2009 3:05:28 PM
Section Name .
.
.
.
.
.
.
.
.
: E10F0.6.1.1
Hardware ID .
.
.
.
.
.
.
.
.
.
: pci\ven_8086&dev_10f0
Instance Status Flags .
.
.
.
.
: 0x180200a
Device Manager Status Code .
.
: 0
IfType .
.
.
.
.
.
.
.
.
.
.
.
: 6
Physical Media Type .
.
.
.
.
.
: 14

Issues found
The default gateway is not available Fixed
Reset the "Local Area Connection" adapter Completed

Intel® Desktop Board DP55WB

Intel® Integrated 10/100/1000 Ethernet Intel® 82567LF

Above are some of the specs I've seen posted that relate to my machine.

My Local Area Connection / Properites / Configure settings:

Adaptive Inter-frame Spacing
Disabled
Enable PME
Disabled
Flow Control
Disabled
Gigabit Master Slave Mode
Auto Detect
Interrupt Moderation                                     Enabled
Interrupt Moderation Rate                             Adaptive
IPv4 Checksum Offload
Rx & Tx Enabled
Large Send Offload (IPv4)
Enabled
Large Send Offload (IPV6)
Enabled
Link Speed &.
Duplex
Auto Negotiation
Locally Administered Address
Not Present Checked
Log Link State Event
Enabled
Priority & VLAN
Priority & VLAN Enabled
Receive Buffers
256
System Idle Power Saver
Disabled
TCP Checksum Offload (IPv4)
Rx & Tx Enabled
TCP Checksum Offload (IPV6)
Rx & Tx Enabled
Transmit Buffers
512
UDP Checksum Offload (IPv4)
Rx & Tx Enabled
UDP Checksum Offload (IPV6)
Rx & Tx Enabled
Wait for link
Auto Detect

Any suggestions on settings changes that will eliminate the problem?
Roxylee

Keys to the Problem Default Gateway Windows 7 64 Bit

Download Error Fixer (Free)

Hey roxylee,
Step1:
You may try to reset WINSOCK, IPv4 TCP/IP, and IPv6 TCP/IP stack.
1.
Click on Start and in the search box, type cmd.
2.
Right click on the Command Prompt, select "Run as Administrator" to open a Command Prompt.
3.
At the command prompt window, type the following commands:
netsh winsock reset catalog that resets WINSOCK entries to installation defaults.
netsh int ipv4 reset reset.log that resets IPv4 TCP/IP stack to installation defaults.
netsh int ipv6 reset reset.log resets IPv6 TCP/IP stack to installation defaults.
4.
Restart the computer.
If you still come across the issue, try the below step.
Step2:
Reset the router to factory defaults by holding the reset button down for 15 seconds with power on.
1.
Turn off the modem, router, and computer.
2.
Connect the modem to the router's WAN/Internet port.
3.
Connect the computer to one of the router's LAN/Network ports.
4.
Turn on the modem, wait for a steady connect light.
5.
Turn on the router, wait for two minutes.
6.
Boot the computer.
7.
When the computer is completely booted, check if the issue persists.
You can also access the below link to reset the TCP\IP Protocol by using Fix it tool which automatically carries out the process:
http://support.microsoft.com/kb/299357
Access the below link which talks about a similar kind of issue you are experiencing:
http://social.answers.microsoft.com/Forums/en-US/w7network/thread/c3ec50e7-d39a-4faf-ad90-d7b961b969bb
I hope the above information helps you.
Give a shot.
Regards,
Manasa P – Microsoft Support.

Manually editing the Windows registry to fix Error Default Gateway Windows 7 64 Bit

Caution: Unless you an advanced PC user, we DO NOT recommend editing the Windows registry manually. Using Registry Editor incorrectly can cause serious problems that may require you to reinstall Windows. We do not guarantee that problems resulting from the incorrect use of Registry Editor can be solved. Use Registry Editor at your own risk.

Click the Start button.
Type "command" in the search box... DO NOT hit ENTER yet!
While holding CTRL-Shift on your keyboard, hit ENTER.
You will be prompted with a permission dialog box.
Click Yes.
A black box will open with a blinking cursor.
Type "regedit" and hit ENTER.
In the Registry Editor, select the Error 0x9C-related key (eg. Windows Operating System) you want to back up.
From the File menu, choose Export.
In the Save In list, select the folder where you want to save the Windows Operating System backup key.
In the File Name box, type a name for your backup file, such as "Windows Operating System Backup".
In the Export Range box, be sure that "Selected branch" is selected.
Click Save.
The file is then saved with a .reg file extension.
You now have a backup of your MACHINE_CHECK_EXCEPTION-related registry entry.

Another Safe way to Fix the Problem: Default Gateway Windows 7 64 Bit:

How to Fix Default Gateway Windows 7 64 Bit with SmartPCFixer?

1. Click the button to download Error Fixer . Install it on your system. Open it, and it will perform a scan for your computer. The junk files will be shown in the scan result.